243 lines
5.5 KiB
C
243 lines
5.5 KiB
C
#ifndef __HERMIT_CRAB_H
|
|
#define __HERMIT_CRAB_H
|
|
#include <Arduino.h>
|
|
|
|
#ifndef ESP32
|
|
#define ESP32
|
|
#endif
|
|
|
|
#define USE_BLE
|
|
#ifdef USE_BLE
|
|
#define THIS_DEVICE_TYPE ENUM_DEVICE_TYPE::TYPE_BETA_BLE
|
|
#define MY_IRAM_ATTR
|
|
#else
|
|
#define THIS_DEVICE_TYPE ENUM_DEVICE_TYPE::TYPE_BETA
|
|
#define MY_IRAM_ATTR IRAM_ATTR
|
|
#endif
|
|
|
|
|
|
// Define DEBUG flag
|
|
#ifndef DEBUG
|
|
#define DEBUG 1 // Set to 0 to disable debug output
|
|
#endif
|
|
#undef DEBUG
|
|
|
|
|
|
//#define BLE_DEBUG
|
|
#ifdef BLE_DEBUG
|
|
#ifndef DEBUG
|
|
#define DEBUG 1
|
|
#endif
|
|
#endif
|
|
|
|
// Debug print macros
|
|
#if defined(DEBUG)
|
|
#define DPRINT(...) Serial.print(__VA_ARGS__)
|
|
#define DPRINTLN(...) Serial.println(__VA_ARGS__)
|
|
#define DPRINTF(...) Serial.printf(__VA_ARGS__)
|
|
#else
|
|
#define DPRINT(...) // Do nothing
|
|
#define DPRINTLN(...) // Do nothing
|
|
#define DPRINTF(...) // Do nothing
|
|
#endif
|
|
|
|
#ifndef SIGNATURE1
|
|
#define SIGNATURE1 ((uint16_t) 0xC8AB)
|
|
#endif
|
|
#ifndef SIGNATURE2
|
|
#define SIGNATURE2 ((uint16_t) 0x4E81)
|
|
#endif
|
|
|
|
|
|
#define KALVIN (273.125f)
|
|
#define LIGHT_ON HIGH
|
|
#define LIGHT_OFF LOW
|
|
#define HUMID_ON HIGH
|
|
#define HUMID_OFF LOW
|
|
#define HEATER_ON HIGH
|
|
#define HEATER_OFF LOW
|
|
#define LED_ON LOW
|
|
#define LED_OFF HIGH
|
|
#define SEGMENT_ON LOW
|
|
#define SEGMENT_OFF HIGH
|
|
|
|
// =======================
|
|
// PIN Definitions
|
|
//
|
|
// LEFT
|
|
#define PIN_NTC 39 // Input Only
|
|
#define PIN_ZCD_LOAD 34 // Input Only
|
|
#define PIN_ZCD_AC 35 // Input Only
|
|
#define PIN_HEATER1 32
|
|
#define PIN_HEATER2 33
|
|
#define PIN_LIGHT 25
|
|
#define PIN_MOTOR 26
|
|
#define PIN_FAN 27
|
|
#define PIN_MIST 14 // Outputs PWM signal at boot
|
|
#define PIN_NONE_1 12 // boot fails if pulled high, strapping pin
|
|
|
|
// BOTTOM
|
|
#define PIN_NONE_2 13
|
|
#define PIN_NONE_6 15 // Outputs PWM signal at Boot, strapping pin
|
|
#define PIN_NONE_5 2
|
|
|
|
// RIGHT
|
|
#define PIN_LED_WIFI 0 // pulled up outputs PWM signal at boot, must be LOW to enter flashing mode
|
|
#define PIN_NONE_4 4
|
|
#define PIN_LED_HEATER2 16
|
|
#define PIN_LED_HEATER1 17
|
|
#define PIN_SW_DOWN 5
|
|
#define PIN_SW_UP 18
|
|
#define PIN_SW_SET 19
|
|
#define PIN_SDA 21
|
|
#define PIN_RX 3
|
|
#define PIN_TX 1
|
|
#define PIN_SCL 22
|
|
#define PIN_NONE_3 23
|
|
// End of PIN Definition
|
|
// =======================
|
|
|
|
|
|
// Resolution for all Channels
|
|
#define PWM_RESOLUTION 10 // 10-bit resolution
|
|
#define PWM_FULL 1023
|
|
#define PWM_OFF 0
|
|
|
|
// High Speed Group - Motor and Fan (26KHz)
|
|
#define PWM_MOTOR_CHANNEL 0
|
|
#define PWM_FAN_CHANNEL 1
|
|
// Medium Speed Group - LED & Heater (1KHz)
|
|
#define PWM_LIGHT_CHANNEL 2
|
|
#define PWM_HEATER1_CHANNEL 3
|
|
#define PWM_HEATER2_CHANNEL 4
|
|
// Low Speed Group - Mist, WifiLED (1Hz)
|
|
#define PWM_MIST_CHANNEL 8
|
|
#define PWM_WIFI_LED_CHANNEL 9
|
|
|
|
#define PWM_1HZ_FREQ 1 // 1 Hz
|
|
#define PWM_1KHZ_FREQ 1221 // 1 kHz
|
|
#define PWM_26KHZ_FREQ 26042 // 26KHz
|
|
|
|
#define TAG "HC"
|
|
|
|
enum EVENT_TYPE {
|
|
// Temperature
|
|
|
|
// Humidity
|
|
|
|
// Light
|
|
|
|
// Fan
|
|
|
|
// Connection
|
|
WiFi_Conneted,
|
|
WiFi_Disconnected,
|
|
BT_Connected,
|
|
BT_Disconnected
|
|
};
|
|
|
|
#define FLAG_MANUAL_HEATER1 (0x0001)
|
|
#define FLAG_MANUAL_HEATER2 (0x0002)
|
|
#define FLAG_MANUAL_MIST (0x0004)
|
|
#define FLAG_MANUAL_FAN (0x0008)
|
|
|
|
#define FLAG_MANUAL_MOTOR (0x0010)
|
|
#define FLAG_MANUAL_LIGHT (0x0020)
|
|
#define FLAG_ZCD_AC (0x0040)
|
|
#define FLAG_ZCD_LOAD (0x0080)
|
|
|
|
#define FLAG_ZCD (0x0100)
|
|
#define FLAG_UPNP (0x0200)
|
|
#define FLAG_BLE_BATT (0x0400)
|
|
#define FLAG_BLE_NODATA (0x0800)
|
|
#define FLAG_BLE_LOST (0x1000)
|
|
|
|
|
|
#pragma pack(push) /* push current alignment to stack */
|
|
#pragma pack(1) /* set alignment to 1 byte boundary */
|
|
typedef struct DEVICE_PARAM_STRUCT {
|
|
uint8_t nControlType;
|
|
uint8_t x;
|
|
uint8_t bDay, bNight;
|
|
//4
|
|
uint16_t dutyMin, dutyMax, dutyStart;
|
|
//6 + 4 = 10
|
|
union {
|
|
uint16_t dutyDay;
|
|
uint16_t dutyOn;
|
|
uint16_t dutyDayOrOn;
|
|
};
|
|
union {
|
|
uint16_t dutyNight;
|
|
uint16_t dutyOff;
|
|
uint16_t dutyNightOrOff;
|
|
};
|
|
//4 + 10 = 14
|
|
int16_t tempHigh, tempLow;
|
|
uint16_t timeBegin, timeEnd;
|
|
uint16_t periodPeriod, periodOn;
|
|
uint16_t humidHigh, humidLow;
|
|
//16 + 14 = 30
|
|
|
|
uint8_t extra[32 - 30];
|
|
} DEVICE_PARAM_TYPE;
|
|
|
|
typedef struct STATUS_STRUCT {
|
|
// Sensor
|
|
int16_t nTemp1;
|
|
int16_t nTemp2;
|
|
int16_t nTemp3;
|
|
int16_t nHumid1;
|
|
int16_t nHumid2;
|
|
// 10
|
|
|
|
// Control
|
|
uint16_t nHeater1Duty; // (0..10000)
|
|
uint16_t nHeater2Duty; // (0..10000)
|
|
uint16_t nMistDuty; //
|
|
uint16_t nFanDuty; //
|
|
uint16_t nMotorDuty;
|
|
uint16_t nLightDuty;
|
|
uint16_t nLightTargetDuty;
|
|
// 24
|
|
|
|
// Current Time
|
|
uint32_t now;
|
|
// 28
|
|
|
|
uint16_t nFlags;
|
|
// 30
|
|
|
|
// AC status
|
|
uint8_t zcdAC;
|
|
uint8_t zcdLoad;
|
|
// 32
|
|
} STATUS_TYPE;
|
|
#pragma pack(pop) /* restore original alignment from stack */
|
|
|
|
// =======================================================
|
|
|
|
char *printStatus(unsigned long tick, bool bLong = false);
|
|
char *printTime(bool bLong = false);
|
|
void checkWiFi(unsigned long tick);
|
|
void checkWiFiHost(unsigned long tick);
|
|
|
|
void core0Task(void *pvParameters);
|
|
|
|
// =======================================================
|
|
|
|
// Status
|
|
extern STATUS_TYPE status;
|
|
|
|
|
|
// Time
|
|
extern volatile unsigned short g_nYear, g_nMonth, g_nDay, g_nHour, g_nMinute, g_nSecond;
|
|
|
|
// Environment
|
|
extern bool bShowSensor;
|
|
extern const char *COMPANY_NAME;
|
|
extern const char *SERVICE_NAME;
|
|
extern const char *HC__VERSION;
|
|
extern volatile uint32_t g_millis;
|
|
#endif
|